Category:Vertical Band Saws -- Metal Cutting: Difference between revisions
From Artisans Asylum Wiki
(→Safety) |
|||
(6 intermediate revisions by the same user not shown) | |||
Line 41: | Line 41: | ||
|} | |} | ||
=Description= | |||
The cutting blade in a band saw is a continuous loop that travels through the machine on pulleys. In a vertical band saw, the blade travels vertically through a slot in a table, and workpieces are hand-fed through the blade to make a cut. | The cutting blade in a band saw is a continuous loop that travels through the machine on pulleys. In a vertical band saw, the blade travels vertically through a slot in a table, and workpieces are hand-fed through the blade to make a cut. | ||
A metal-cutting band saw uses blades | A metal-cutting band saw uses blades that resemble a hack-saw. They are different from a wood-cutting saw. | ||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
Line 54: | Line 54: | ||
|} | |} | ||
'''Three Tooth Rule''' | '''Three-Tooth Rule''' | ||
There should be a minimum of '' | There should be a minimum of ''THREE TEETH'' of the saw blade engaged in a cut. If there are too few teeth in the cut, the advancing stock can catch too much of a blade tooth and shear it off. Teeth can be ejected into the user's face. In a less severe case the blade may be stalled. | ||
{{EyeWarning}} | {{EyeWarning}} | ||
=Safety= | |||
==Personal== | ==Personal== | ||
* '''Wear safety goggles.''' Eyeglasses are NOT safety goggles. | * '''Wear safety goggles.''' Eyeglasses are NOT safety goggles. | ||
Line 72: | Line 71: | ||
* '''Do not wear loose clothing''' or jewelry when operating the machine. Long hair must be tied back or covered. | * '''Do not wear loose clothing''' or jewelry when operating the machine. Long hair must be tied back or covered. | ||
* Do not wear gloves. Gloves can be drawn into a cut by the moving blade. | * Do not wear gloves. Gloves can be drawn into a cut by the moving blade. | ||
* '''Keep fingers away from the line of cut.''' Use a push-stick or fixture | |||
* Do not remove chips from the cutting area with bare hands. Use a chip brush. | * Do not remove chips from the cutting area with bare hands. Use a chip brush. | ||
* Always keep a secure, stable stance. Avoid over-reaching. Clean up oil spills immediately and avoid slipping. Keep the work area clear of trip hazards. | * Always keep a secure, stable stance. Avoid over-reaching. Clean up oil spills immediately and avoid slipping. Keep the work area clear of trip hazards. | ||
Line 77: | Line 77: | ||
==Machine== | ==Machine== | ||
* Make sure all guards and covers are in place | |||
* Lower the blade guard to within 3/8" of the highest point on the workpiece. | |||
* Always stay at the machine while it is running. | * Always stay at the machine while it is running. | ||
* Keep the workpiece flat against the table and hold firmly. Irregular stock risks jamming the blade. | |||
* When cutting round stock, clamp it securely in a vise to prevent it from rolling on the blade. | |||
* Use cutting oil. | |||
* Do not operate the machine if any unusual or excessive heat, noise, smoke, or vibration occurs. | * Do not operate the machine if any unusual or excessive heat, noise, smoke, or vibration occurs. | ||
* '''Make sure the blade has come to a complete stop''' before removing the workpiece from a partial cut. | * '''Make sure the blade has come to a complete stop''' before removing the workpiece from a partial cut. | ||
* Do not allow loose tools or piles of chips to accumulate on the machine. | * Do not allow loose tools or piles of chips to accumulate on the machine. | ||
* Always use sharp blades that are in good condition. | * Always use sharp blades that are in good condition. |
Latest revision as of 19:43, 16 March 2024
Link to: Machine Shop Main Page
Eye protection required! | ||
---|---|---|
Metal-Cutting Vertical Band Saws | |
---|---|
General Info | |
Make | various |
Model | |
Serial | |
Specs | |
Manual | |
Asylum Info | |
Location | Machine Shop |
Rubric | N/A |
Training | |
Testing | Tool testing |
Restrictions | red |
Use For | Do Not Use For |
---|---|
|
|
Description
The cutting blade in a band saw is a continuous loop that travels through the machine on pulleys. In a vertical band saw, the blade travels vertically through a slot in a table, and workpieces are hand-fed through the blade to make a cut.
A metal-cutting band saw uses blades that resemble a hack-saw. They are different from a wood-cutting saw.
Parts of a typical band saw. |
Three-Tooth Rule
There should be a minimum of THREE TEETH of the saw blade engaged in a cut. If there are too few teeth in the cut, the advancing stock can catch too much of a blade tooth and shear it off. Teeth can be ejected into the user's face. In a less severe case the blade may be stalled.
Eye protection required! | ||
---|---|---|
Safety
Personal
- Wear safety goggles. Eyeglasses are NOT safety goggles.
- Wear closed-toe shoes.
- Do not wear loose clothing or jewelry when operating the machine. Long hair must be tied back or covered.
- Do not wear gloves. Gloves can be drawn into a cut by the moving blade.
- Keep fingers away from the line of cut. Use a push-stick or fixture
- Do not remove chips from the cutting area with bare hands. Use a chip brush.
- Always keep a secure, stable stance. Avoid over-reaching. Clean up oil spills immediately and avoid slipping. Keep the work area clear of trip hazards.
Machine
- Make sure all guards and covers are in place
- Lower the blade guard to within 3/8" of the highest point on the workpiece.
- Always stay at the machine while it is running.
- Keep the workpiece flat against the table and hold firmly. Irregular stock risks jamming the blade.
- When cutting round stock, clamp it securely in a vise to prevent it from rolling on the blade.
- Use cutting oil.
- Do not operate the machine if any unusual or excessive heat, noise, smoke, or vibration occurs.
- Make sure the blade has come to a complete stop before removing the workpiece from a partial cut.
- Do not allow loose tools or piles of chips to accumulate on the machine.
- Always use sharp blades that are in good condition.
Pages in category "Vertical Band Saws -- Metal Cutting"
The following 2 pages are in this category, out of 2 total.