Cyclone Sand Blaster: Difference between revisions

From Artisans Asylum Wiki
No edit summary
No edit summary
Line 110: Line 110:


* Do not point the blast gun at the rubber gloves or the cabinet window.
* Do not point the blast gun at the rubber gloves or the cabinet window.
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Metal_shop_lead_test_swabs.jpg|500px|blade flange]]
|-
| colspan="2" | Lead test swabs container
|-
|}

Revision as of 17:37, 24 April 2024


Link to: Metal Shop main page



Sand Blaster
A Happy Blaster
General Info
Make Cyclone Manufacturing
Model DW-7335
Serial Unknown
Specs
Manual
Asylum Info
Location Metal Shop
Rubric
Training Tool classes
Testing Tool testing, or [[:Category:Metal Shop#Tool Testing

Night|come to the shop on Tool Testing Night]]

Restrictions green


Goggle mask.png
Blaster dust hazard.png
No lead warning.png


Warning Safety glasses Eye protection required!



Description

A sand blaster is a machine that mixes abrasive grains with a jet of compressed air and allows the user to abrade the surface of a part, usually metal. This results in a clean though roughened part free of paint, rust, and other forms of dirt. For smaller parts the blast gun is contained in a glovebox cabinet sealed off from the outside. The user manipulates the tool with thick rubber gloves that pass through the wall of the cabinet.

The sand blaster cabinet at Artisans Asylum is located in a small room within the Metal Shop on the south wall adjacent to the enclosed loading dock.

Use For

  • Steel
  • Stainless Steel
  • Zinc-coated steel (Galvanized)
  • Aluminum, Titanium, Brass
  • Painted metal
  • Lightly Rusted Parts

Do Not Use For

  • Lead-based paints
  • Asbestos
  • Greasy or Oily Parts
  • Massively Rusty Parts

Use a lead-test swab to verify that paint if NOT lead-based!

If the sandblaster becomes contaminated with lead the media must be disposed as TOXIC WASTE and the cabinet must be thoroughly cleaned out!

Safety Notes

Personal

Goggle mask.png
  • Wear safety goggles. Eyeglasses don't protect against abrasive dust.
  • Wear a dust mask or respirator when using the machine or working in the room when the machine is being used. All dust is hazardous to breathe.
  • Glove-box gloves are at a fixed height above the floor. If they are too high, a stand should be provided. Use care when stepping on and off the stand.
  • If the blast gun is not properly grounded to the cabinet, static electricity can cause shocks to the operator. If static shocks are encountered, check the ground connection to the gun.
  • Do not use silica sand as an abrasive media. The preferred sand blasting media is aluminum oxide.
  • Use caution when lifting heavy parts into the sandblaster cabinet.
  • If a part is too large to allow the hatch to close and seal, then do not operate the sandblaster.
  • Use caution with the foot pedal and hoses. They are a trip hazard.

Machine

  • Test paints and coatings for LEAD using the test swabs provided. The swabs change from yellow to red when lead is present. If lead is detected do not clean with the sand blaster.
  • Do not abrade greasy or oily parts in the sandblaster. These will case the media to clump and clog the flow lines. If it happens, the media must be replaced.
  • Place the workpiece in the blast cabinet and close the hatch tightly to avoid dust escaping from the cabinet. When removing workpieces, some dust will unavoidably mix with the room air. Wear a dust mask at all times.
  • Do not attempt to move the blast cabinet when it is full of abrasive media.
  • Do not point the blast gun at the rubber gloves or the cabinet window.
blade flange
Lead test swabs container