|
Tags: Blanking Manual revert |
(10 intermediate revisions by the same user not shown) |
Line 1: |
Line 1: |
| [[Category:Tools]][[Category:Metal Shop]]
| |
|
| |
|
| {{ToolBox|tool_title=48-inch Jump Shear|image=Metal_Shop_jump_shear_nolabels.png|caption=Jet 48-inch Jump Shear|
| |
| location=Metal Shop|training=[https://www.artisansasylum.com/class-catalog Tool classes]|testing=
| |
| [https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing
| |
| Night|come to the shop on Tool Testing Night]]|restrictions=green|make=Jet|model=FS-1636N|
| |
| serial=Unknown|manufacturer_specs=n/a|manual=[https://drive.google.com/file/d/1dkSvgaDHEOI-oTHDXDp6ET00QeXu0oSx/view?usp=drive_link Manual]|rubric=n/a|tool_categories=}}
| |
|
| |
| ==Use for:==
| |
|
| |
| * Up to 16 ga (0.0625") sheet metal, any metal is okay
| |
|
| |
| * Note that different metals have different thickness limits.
| |
|
| |
| ==Do Not Use for:==
| |
|
| |
| * Any sheet metal exceeding max thickness
| |
|
| |
| ==Hazard Analysis==
| |
|
| |
| * The workpiece can snap unexpectedly or break. Eye Protection Required
| |
|
| |
| * Caught-between injuries when cutting
| |
|
| |
| * Don’t pinch hands in the machine’s moving parts
| |
|
| |
| * Don’t smash a foot under the foot petal
| |
|
| |
| * Shin injuries from slipping off the foot pedal
| |
|
| |
| * Cuts/ scrapes from sharp cut edges of work
| |
|
| |
| {{EyeWarning}}
| |
|
| |
| {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
| |
| ! colspan="2" class="infobox-image" | [[File:Metal_Shop_jump_shear_thickness_capacity.png|300px|thickness equivalents]]
| |
| |-
| |
| | colspan="2" | Equivalent thickness for shearing different metals relative to mild steel.
| |
| |-
| |
| |}
| |
|
| |
| ==Operation Notes==
| |
|
| |
| * To perform multiple cuts of the same length, use the backstop and front stop attachments (stored under the pan and box brake).
| |
|
| |
| * Thickness limits are different for different metals.
| |
|
| |
| '''Refer to the chart on the machine'''
| |
|
| |
| ==Basic Operation Instructions==
| |
|
| |
| '''Test before use - make sure blades are not interfering with each other.'''
| |
|
| |
| 1. Step on Foot Lever
| |
|
| |
| 2. As the foot lever travels downward, the Hold Down will press against the work piece at about half way. The Foot Lever will stop at this point.
| |
|
| |
| {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
| |
| ! colspan="2" class="infobox-image" | [[File:Metal_Shop_jump_shear_hold_down.png|450px|foot lever and hold down]]
| |
| |-
| |
| | colspan="2" | The foot lever and hold down on the jump shear.
| |
| |-
| |
| |}
| |
|
| |
| 3. To engage the cutting blade and perform the cut, use both feet to “jump" on the Foot Lever and press it to the floor.
| |
|
| |
| '''Test with Craft Paper''' A paper grocery bag works well.
| |
|
| |
| {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
| |
| ! colspan="2" class="infobox-image" | [[File:Metal_Shop_jump_shear_rear_adjustment_screws.png|450px|rear adjustments]]
| |
| |-
| |
| | colspan="2" | Adjustment screws on the rear of the jump shear, for the upper blade.
| |
| |-
| |
| |}
| |
|
| |
| {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
| |
| ! colspan="2" class="infobox-image" | [[File:Metal_Shop_jump_shear_front_adjustment_screws.png|450px|front adjustments]]
| |
| |-
| |
| | colspan="2" | Adjustment screws on the front and sides of the jump shear, for the lower blade.
| |
| |-
| |
| |}
| |
|
| |
|
| |
| * '''If the shear cuts paper on the ends but not the center,''' loosen the hex nut and turn the tie-rod adjusting screw clockwise, as viewed from back, until paper is cut the entire length.
| |
|
| |
| * '''If the shear cuts paper in the center but not the ends,'' loosen the hex nut and turn the tie-rod adjusting screw counter-clockwise until the paper is cut the entire length.
| |
|
| |
| * Retighten the hex nut against the frame.
| |
|
| |
| * To adjust the bottom blade, loosen the large bolts on the sides and adjust with bolts on the front.
| |
|
| |
| ==Video==
| |
|
| |
| https://www.youtube.com/watch?v=S0Vl77nS_5U&t=2s Use of the jump shear]
| |