Uploads by Dankulla
From Artisans Asylum Wiki
This special page shows all uploaded files.
| Date | Name | Thumbnail | Size | Description | Versions |
|---|---|---|---|---|---|
| 18:10, 18 March 2024 | Dan Kulla.jpg (file) |  |
381 KB | 1 | |
| 19:38, 18 March 2024 | Ariel matisse.jpeg (file) |  |
30 KB | 1 | |
| 17:34, 19 March 2024 | Alison waters doherty.jpeg (file) |  |
157 KB | 1 | |
| 17:39, 19 March 2024 | Rosa weinberg.png (file) |  |
1.4 MB | 1 | |
| 17:41, 19 March 2024 | Peter feary.jpeg (file) |  |
181 KB | 1 | |
| 17:44, 19 March 2024 | Tom cole.jpeg (file) |  |
60 KB | 1 | |
| 17:47, 19 March 2024 | Puppy (Joe Wight).png (file) | .png) |
2.35 MB | 1 | |
| 17:49, 19 March 2024 | Lewis bryant.jpeg (file) |  |
25 KB | 1 | |
| 17:52, 19 March 2024 | Nicholas bernier.jpeg (file) |  |
33 KB | 1 | |
| 17:54, 19 March 2024 | Scraps sparcs.jpeg (file) |  |
103 KB | 1 | |
| 17:56, 19 March 2024 | Morgan pierson.png (file) |  |
474 KB | 1 | |
| 17:58, 19 March 2024 | Geoff chasin.png (file) |  |
65 KB | 1 | |
| 18:01, 19 March 2024 | Alice stein.jpeg (file) |  |
464 KB | 1 | |
| 18:26, 19 March 2024 | Mike mittelman.jpg (file) |  |
36 KB | 1 | |
| 19:49, 2 April 2024 | Eccentric.png (file) |  |
37 KB | this is a bullseye where none of the circle components share the same center. | 1 |
| 19:50, 2 April 2024 | Concentric.png (file) |  |
37 KB | This is a bullseye where all of the circle components share the same center | 1 |
| 19:37, 12 April 2024 | Sb motor and belts.jpeg (file) |  |
1.21 MB | The motor and two sets of pulleys in the South Bend metal lathe powertrain | 1 |
| 20:10, 12 April 2024 | Sb back gear and locking pin.jpeg (file) |  |
1.56 MB | overview of the south bend headstock spindle speed controls | 1 |
| 20:23, 12 April 2024 | Sb power feed settings.jpeg (file) |  |
1.62 MB | Overview of power feed and threading headstock controls on the South Bend lathe | 1 |
| 20:33, 12 April 2024 | Sb apron controls.jpeg (file) |  |
1.62 MB | overview of South Bend apron controls | 1 |
| 20:41, 12 April 2024 | Sb removing chuck.jpeg (file) |  |
448 KB | removing a chuck from the South Bend lathe | 1 |
| 20:51, 12 April 2024 | Sb motor and belts annotated.jpeg (file) |  |
1.38 MB | an annotated photo of the South Bend motor, belts, and pulleys | 2 |
| 21:26, 12 April 2024 | Logan clutch collar engaged.jpeg (file) |  |
919 KB | Logan clutch collar engaged with the spindle | 1 |
| 21:27, 12 April 2024 | Logan clutch collar disengaged.jpeg (file) |  |
939 KB | Logan clutch collar disengaged from the spindle | 1 |
| 21:34, 12 April 2024 | Logan headstock controlls.jpeg (file) |  |
1.64 MB | Overview of the Logan lathe headstock controls, including the back gear lever, the power feed direction selector, and the feed rate/thread pitch adjustment | 1 |
| 21:51, 12 April 2024 | Logan apron controls.jpeg (file) |  |
1.51 MB | updated version: use "power feed" names instead of "auto feed" to be consistent with article text. | 2 |
| 21:53, 12 April 2024 | Logan chuck removal.jpeg (file) |  |
1.53 MB | Yours Truly, removing a chuck from the Logan Lathe | 1 |
| 22:13, 12 April 2024 | Logan collet closer components.jpeg (file) |  |
1.39 MB | overview of the Logan's 5C collet closer setup | 1 |
| 22:22, 12 April 2024 | Logan collet closer headstock.jpeg (file) |  |
1.41 MB | Overview of the headstock end of the Logan collet closer | 1 |
| 22:26, 12 April 2024 | Logan collet closer adjustment locked.jpeg (file) |  |
1.17 MB | the locking tab is down, so the collet closer adjustment is locked in place. | 1 |
| 22:27, 12 April 2024 | Logan collet closer adjustment.jpeg (file) |  |
1.22 MB | the locking tab is up, so the collet closer adjustment is unlocked, and the collet closer tension can be adjusted. | 1 |
| 22:28, 12 April 2024 | Logan collet closer at home.jpeg (file) |  |
1.35 MB | When it's not in use, the Logan collet closer lives on a mount behind the lathe. | 1 |
| 14:12, 11 May 2024 | ArtisansAsylum Bylaws2018.pdf (file) |  |
409 KB | This is the most recent version of the bylaws, which was amended January 17, 2018 | 1 |
| 15:20, 5 September 2024 | Square lathe tool top view.png (file) |  |
13.41 MB | A view of a squared off lathe tool from the top. The highlighted faces rub will rub against each other during a cut. | 1 |
| 15:21, 5 September 2024 | Square lathe tool front view.png (file) |  |
14.15 MB | View of a squared off lathe tool from the front. The highlighted surfaces will rub against each other during a cut. | 1 |
| 14:50, 17 September 2024 | Lathe coordinate system.jpg (file) |  |
18 KB | The X and Z axes of a lathe. The carriage moves along the Z axis, which gets increasingly positive as the carriage moves away from the headstock. The cross slide moves along the X axis, which gets increasingly positive as the cross slide moves away from the operator side. | 1 |
