Category:Powder Coating Facility: Difference between revisions
No edit summary |
|||
| Line 75: | Line 75: | ||
* '''Wear a dust mask and eye goggles.''' Eyeglasses are not goggles. | * '''Wear a dust mask and eye goggles.''' Eyeglasses are not goggles. | ||
* Wear heat-resistant gloves when handling hot parts | |||
* Keep the pressure set to below 10 psi. 3 Psi is recommended. | |||
* '''Always run the fan on the spray booth when operating the coating equipment.''' | |||
{| class="infobox" cellspacing="0" style="width: 2em; text-align: left; font-size: 125%; line-height: 1.5em;" | {| class="infobox" cellspacing="0" style="width: 2em; text-align: left; font-size: 125%; line-height: 1.5em;" | ||
! colspan="2" class="infobox-image" | [[File:_pacemaker_warning.png|100px| ]] | ! colspan="2" class="infobox-image" | [[File:_pacemaker_warning.png|100px| ]] | ||
| Line 81: | Line 87: | ||
|- | |- | ||
|} | |} | ||
* Dense clouds of powder are flammable. Keep flames away from the machine during coating. | * Dense clouds of powder are flammable. Keep flames away from the machine during coating. | ||
Revision as of 14:06, 20 May 2024
Link to: Metal Shop main page
| Powder Coating | |
|---|---|
| General Info | |
| Make | |
| Model | |
| Serial | Unknown |
| Specs | |
| Manual | Manual for the smaller gun |
| Asylum Info | |
| Location | Metal Shop |
| Rubric | |
| Training | Tool classes |
| Testing | Tool testing, or [[:Category:Metal Shop#Tool Testing
Night|come to the shop on Tool Testing Night]] |
| Restrictions | green |
 |
 |
Eye protection required! |
|---|---|---|
Description
| |
|---|---|
Located in a room on the southern wall of the Metal Shop, between the sand-blasting room and the CNC plasma cutter. This facility is sized to accommodate bicycle frames. A rolling rack holds the workpieces in an 8'x8'x8' spray booth and then transfers to a 4'x4'x8' box oven. Two guns are available, and many jars of colored paints are present in the shop. The spray booth is vented inside the room after filtering the airflow.
The process uses dry powdered paint that is applied with a pneumatic gun that includes a high-voltage electrode. As the powder passes by the electrode it becomes electrically charged. The metallic workpiece is grounded and so it attracts the charged paint particles. After coating, workpieces are baked in a convection oven to fuse the paint.
Films made by powder coating are up to ten times more durable than those made with liquid paint. The coatings are essentially fused plastic, and so they resist chemicals and salt exceptionally well. Further, the process produces no organic fumes or toxic waste. Unfortunately the literature recommends cleaning workpieces with acetone, so organic fumes are still present.
Use For
Clean metal parts.
Weldments
Brazed parts
Forgings
Castings
Sheet metal
Steel, Stainless, Galvanized, Aluminum, Titanium, etc.
Do Not Use For
Dirty, rusty, or flaky metal parts.
Nonconductive plastic, wooden, or ceramic parts.
Parts that can't tolerate heating to 400°F (200°C)
Safety Notes
| |
|---|---|
- Danger of electric shock. Don't touch the gun electrode while the activation button is pressed.
- Don't touch grounded workpieces or racks when operating the coating gun.
- Wear a dust mask and eye goggles. Eyeglasses are not goggles.
- Wear heat-resistant gloves when handling hot parts
- Keep the pressure set to below 10 psi. 3 Psi is recommended.
- Always run the fan on the spray booth when operating the coating equipment.
| |
|---|---|
- Dense clouds of powder are flammable. Keep flames away from the machine during coating.
- Don't over-reach, keep proper balance at all times.
- The room will tend to overheat if the oven is operated for a long time.
- Avoid trip hazards. The room is small and there is a lot of equipment in there.
- Don't use the ovens in the shop for heating food.
| Spray Booth | Eastwood Dual-Voltage Gun | HICOLO Fab 660 System | Box Oven |
|---|---|---|---|
 |
 |
 |
|
Pages in category "Powder Coating Facility"
The following 4 pages are in this category, out of 4 total.
