Box and Pan Brake: Difference between revisions
From Artisans Asylum Wiki
No edit summary |
No edit summary |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Tools]][[Category:Metal Shop]] | |||
Link to: [[:Category:Metal Shop | Metal Shop main page]] | |||
Link to: [[:Category:Metal Shop#Tools | Metal Shop tool list]] | |||
Night|come to the shop on Tool Testing Night]]|restrictions= | {{ToolBox|tool_title=Box and Pan Brake|image=Metal_shop_brake_nolabels.jpg|caption=Box and Pan Brake|location=Metal Shop|training=[https://www.artisansasylum.com/class-catalog Tool classes]|testing=[https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing Night|come to the shop on Tool Testing Night]]|restrictions=green|make=Varied|model=Varied|serial=Unknown|manufacturer_specs=n/a|manual=n/a|rubric=n/a|tool_categories=}} | ||
serial=Unknown|manufacturer_specs=n/a|manual=n/a|rubric=n/a|tool_categories=}} | |||
== Materials == | == Materials == | ||
| Line 18: | Line 16: | ||
=== Do not use for: === | === Do not use for: === | ||
* Sheet metal exceeding 1/32" | * Sheet metal exceeding 1/32" thickness | ||
* Stainless steel | * Stainless steel | ||
* High-carbon or Hardened steel | * High-carbon or Hardened steel | ||
| Line 24: | Line 22: | ||
== Safety Hazards == | == Safety Hazards == | ||
{{EyeWarning}} | {{EyeWarning}} | ||
| Line 29: | Line 28: | ||
* Pinching injuries | * Pinching injuries | ||
* Cuts/scrapes from sharp edges and burrs | |||
== Operation Notes == | |||
| Line 38: | Line 41: | ||
|} | |} | ||
* Brake maximum capacity – 22 GA x 48” width | * Brake maximum capacity – 22 GA x 48” width | ||
Latest revision as of 21:07, 5 September 2024
Link to: Metal Shop main page
Link to: Metal Shop tool list
| Box and Pan Brake | |
|---|---|
| General Info | |
| Make | Varied |
| Model | Varied |
| Serial | Unknown |
| Specs | n/a |
| Manual | n/a |
| Asylum Info | |
| Location | Metal Shop |
| Rubric | n/a |
| Training | Tool classes |
| Testing | Tool testing, or come to the shop on Tool Testing Night |
| Restrictions | green |
Materials
Use for:
- Up to 22 Ga sheet metal (1/32")
- Mild Steel
- Soft Metals
Do not use for:
- Sheet metal exceeding 1/32" thickness
- Stainless steel
- High-carbon or Hardened steel
- Round or square stock
Safety Hazards
 |
 |
Eye protection required! |
|---|---|---|
- Workpiece can unexpectedly snap
- Pinching injuries
- Cuts/scrapes from sharp edges and burrs
Operation Notes
| |
|---|---|
| Metal Shop Sheet Metal Brake |
- Brake maximum capacity – 22 GA x 48” width
- Attached gauge wheel is used to judge if your material is appropriate for the machine.
- Spare parts, including an Allen wrench, are stored underneath.
- A 6 mm Allen wrench is used to adjust fingers. The proper size wrench will help to prolong the life of the screw heads.
Basic Operating Instructions
| |
|---|---|
| Parts of the Brake |
| |
|---|---|
| Adjusting the Brake |
- Align fingers by loosening all, then raising the apron to line them up. Re-tighten.
- Place sheet metal under fingers and position as needed.
- Use a 6 mm Allen wrench to adjust fingers 1/18” to 1/16” from edge. Material width from edge is a good rule of thumb.
- Lock your material by pressing both clamp handles down. (Left one is bent, and tricky)
- To bend sheet metal, grab Apron Handles and lift. (Remember, steel has spring-back.)
