Hydraulic Shop Press: Difference between revisions
No edit summary |
No edit summary |
||
| (One intermediate revision by the same user not shown) | |||
| Line 7: | Line 7: | ||
This tool is used in [[:Brackets_Tutorial_2b:_Fabricating_a_Bracket_from_a_Solidworks_Design#Bend_the_Sheet | Brackets tutorial 2b]] and [[:Brackets_Tutorial_3:_No_Frills_Shelf_Bracket#Bend_the_Bracket | Brackets tutorial 3.]] | This tool is used in [[:Brackets_Tutorial_2b:_Fabricating_a_Bracket_from_a_Solidworks_Design#Bend_the_Sheet | Brackets tutorial 2b]] and [[:Brackets_Tutorial_3:_No_Frills_Shelf_Bracket#Bend_the_Bracket | Brackets tutorial 3.]] | ||
{{ToolBox|tool_title=12-Ton Shop Press|image=SW_3_BracketRE_16_press.png|caption=Shop press for bending|location=Metal Shop|training=[https://www.artisansasylum.com/class-catalog Tool classes]| | {{ToolBox | ||
testing=[https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing Night|come to the shop on Tool Testing Night]]|restrictions=green|make=Duralast|model=12-ton| | |tool_title=12-Ton Shop Press | ||
serial=Unknown|manufacturer_specs=n/a|manual= | |image=SW_3_BracketRE_16_press.png | ||
|caption=Shop press for bending | |||
|location=Metal Shop | |||
|training=[https://www.artisansasylum.com/class-catalog Tool classes] | |||
|testing=[https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing Night|come to the shop on Tool Testing Night]] | |||
|restrictions=green | |||
|make=Duralast | |||
|model=12-ton | |||
|serial=Unknown | |||
|manufacturer_specs=n/a | |||
|manual= [https://drive.google.com/file/d/1Nuy2IyIoAondwi9wheXuH1nB-s5gW41K/view?usp=drive_link 12-ton bottle jack manual] | |||
|rubric=n/a | |||
|tool_categories= | |||
}} | |||
= Description = | = Description = | ||
Latest revision as of 13:57, 12 October 2024
Link to: Metal Shop main page
Link to: Metal Shop tool list
This tool is used in Brackets tutorial 2b and Brackets tutorial 3.
| 12-Ton Shop Press | |
|---|---|
| General Info | |
| Make | Duralast |
| Model | 12-ton |
| Serial | Unknown |
| Specs | n/a |
| Manual | 12-ton bottle jack manual |
| Asylum Info | |
| Location | Metal Shop |
| Rubric | n/a |
| Training | Tool classes |
| Testing | Tool testing, or come to the shop on Tool Testing Night |
| Restrictions | green |
Description
| |
|---|---|
| Pressure relief |
This is a 12-ton hydraulic "bottle" jack mounted to a steel frame so it can be used as a press. The pressure relief valve is located on the press base. This machine is generally used for bending sheets and bars, and it usually has a 4" wide right-angle bending tool and die set mounted. The opening in the frame is 16" wide.
Use for:
- Bending steel sheets and bars up to 1/8" thick
Do not use for:
- High-carbon or Hardened steel
- Round or square stock
Safety Hazards
 |
 |
Eye protection required! |
|---|---|---|
- Workpiece can unexpectedly snap
- Pinching injuries
- Cuts/scrapes from sharp edges and burrs
Bending
- Mark your workpiece with a clearly visible line.
| |
|---|---|
| Bend |
| |
|---|---|
| Square |
| |
|---|---|
| Mark |
- Insert the workpiece into the jig and lower the workpiece so it lightly loads.
- Square the workpiece in the tool.
- Pump up the pressure to bend the workpiece.
- Check the angle with a square as the bend approaches 90°. If you squeeze too far, the bend can surpass 90°.
Tooling
| |
|---|---|
| Removing the tool with a "dead-blow" hammer. |
| |
|---|---|
| Longitudinal bending tool. |
| |
|---|---|
| Transverse bending tool. |
The bending tool is press-fit onto the ram below the bottle jack. It can be positioned at any angle, but the two most useful orientations are shown here: longitudinal and transverse.
To remove the tool, hit it with a "dead-blow" hammer with a soft head until it lossens up and comes off. Reposition, and press it onto the ram using the press.
