Powermatic PJ1696 Jointer: Difference between revisions
No edit summary |
No edit summary |
||
(35 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
[[Category:Tools]][[Category:Wood Shop]] | [[Category:Tools]] | ||
Link to: [[:Category:Wood Shop | Wood Shop main page]] | |||
{{ToolBox | {{ToolBox | ||
Line 10: | Line 11: | ||
|serial = Unknown | |serial = Unknown | ||
|manufacturer_specs = | |manufacturer_specs = | ||
|manual = [ | |manual = [[media: Jointer_Powermatic_PJ1696_16_inch_Manual.pdf | Jointer User Manual]] | ||
|location = Wood Shop | |location = Wood Shop | ||
|rubric = | |rubric = | ||
Line 19: | Line 20: | ||
}} | }} | ||
'''This is a | '''This is a <span style="color:red">red</span> tool. Training and tool-testing are required.''' | ||
{{EyeWarning}} | |||
==Description== | |||
A jointer has a similar architecture to a table saw. Workpieces are fed by hand on a flat table and a rotating cutter projects through the table top. Unlike a table saw, the jointer cutter is cylindrical and mills the bottom surface of the workpiece to flatten it out. | |||
==Use For== | ==Use For== | ||
Line 26: | Line 33: | ||
Length > 8 inches | Length > 8 inches | ||
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_nolabels.jpg|320px|Jointer nolabels]] | |||
|- | |||
| colspan="2" | The Powermatic Jointer waiting to be used | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_knife_rotor.png|220px|Jointer knives]] | |||
|- | |||
| colspan="2" | WHIRLING KNIVES! | |||
|- | |||
|} | |||
Width > 3/4" | Width > 3/4" | ||
Line 40: | Line 61: | ||
Metals | Metals | ||
==Safety Notes== | ==Safety Notes== | ||
Line 47: | Line 66: | ||
'''Personal:''' | '''Personal:''' | ||
* Eye protection required | {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
! colspan="2" class="infobox-image" | [[File:Jointer_three_inch_hand_radius.png|320px|Jointer 3 inch]] | |||
|- | |||
| colspan="2" | Don't chop off your fingers! | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="0" style="width: 2em; text-align: left; font-size: 125%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:headphones_goggles.png|60px| ]] | |||
|- | |||
| colspan="2" | | |||
|- | |||
|} | |||
* '''Eye protection required''' | |||
* Hearing protection recommended | * '''Hearing protection recommended''' | ||
* No loose clothing or jewelry, roll up sleeves above the elbows. | * '''No loose clothing''' or jewelry, roll up sleeves above the elbows. | ||
* Tie up or cover long hair | * Tie up or cover long hair | ||
Line 59: | Line 92: | ||
'''Tool:''' | '''Tool:''' | ||
* Make sure guards are in place and working well. | * Make sure the guards are in place and working well. | ||
* Switch on Dust Collector: Coral 2-filter between Jointer and Planer | * '''Switch on the Dust Collector:''' Coral AF/2C free-standing 2-filter between the 1696 Jointer and the 201 Planer ("The Beast".) | ||
* Keep hands at least 3 inches away from the blades at all times. | * Keep hands at least 3 inches away from the blades at all times. | ||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_hand_choreography.png|320px|Jointer hand choreography]] | |||
|- | |||
| colspan="2" | Shift hands during cut. MAINTAIN PRESSURE ON THE WORKPIECE. | |||
|- | |||
|} | |||
* Don't cut wood less than 8" long, 3/4" wide or 1/4" thick. | * Don't cut wood less than 8" long, 3/4" wide or 1/4" thick. | ||
Line 75: | Line 115: | ||
* Never make cuts greater then 1/8" deep | * Never make cuts greater then 1/8" deep | ||
* Do NOT wear gloves | |||
==Setting the Outfeed Table Height== | |||
1. Raise the outfeed to its highest point and place a straight edge across the cutter. | |||
2. Turn the cutter head until one row of knives is at its highest point. | |||
3. Lower the outfeed table until the straight edge contacts a knife blade. Rock the head slightly to make sure the apex of the knife is contacting the straight edge. | |||
4. Lock the outfeed table at this setting. | |||
{| class="wikitable" | |||
|+ Jointer Outfeed Table Height | |||
|- | |||
! Too high !! Just right !! Too low | |||
|- | |||
| Workpiece curved on bottom || Workpiece flat on bottom || Workpiece gouged at end | |||
|- | |||
| [[File:Jointer_outfeed_high.png|350px]] || [[File:Jointer_outfeed_correct.png|350px]] || [[File:Jointer_outfeed_low.png|350px]] | |||
|} |
Latest revision as of 13:50, 11 June 2024
Link to: Wood Shop main page
Powermatic 16" Jointer | |
---|---|
General Info | |
Make | Powermatic |
Model | PJ1696 |
Serial | Unknown |
Specs | |
Manual | Jointer User Manual |
Asylum Info | |
Location | Wood Shop |
Rubric | |
Training | |
Testing | |
Restrictions | red |
This is a red tool. Training and tool-testing are required.
Eye protection required! | ||
---|---|---|
Description
A jointer has a similar architecture to a table saw. Workpieces are fed by hand on a flat table and a rotating cutter projects through the table top. Unlike a table saw, the jointer cutter is cylindrical and mills the bottom surface of the workpiece to flatten it out.
Use For
Wooden boards only
Length > 8 inches
The Powermatic Jointer waiting to be used |
WHIRLING KNIVES! |
Width > 3/4"
Wood with uneven grain requires special care.
Do Not Use For
Fiberboard
Plastics
Composites
Metals
Safety Notes
Personal:
Don't chop off your fingers! |
- Eye protection required
- Hearing protection recommended
- No loose clothing or jewelry, roll up sleeves above the elbows.
- Tie up or cover long hair
- Closed-toe shoes with good traction.
Tool:
- Make sure the guards are in place and working well.
- Switch on the Dust Collector: Coral AF/2C free-standing 2-filter between the 1696 Jointer and the 201 Planer ("The Beast".)
- Keep hands at least 3 inches away from the blades at all times.
Shift hands during cut. MAINTAIN PRESSURE ON THE WORKPIECE. |
- Don't cut wood less than 8" long, 3/4" wide or 1/4" thick.
- For wood less than 12" long, 3" wide and 3" thick, a hold-down or push block is required
- Never apply pressure to stock directly above the cutter head. This can lead to the stock tipping into the cutter.
- Wood grain must run in the direction of the cutting.
- Never make cuts greater then 1/8" deep
- Do NOT wear gloves
Setting the Outfeed Table Height
1. Raise the outfeed to its highest point and place a straight edge across the cutter.
2. Turn the cutter head until one row of knives is at its highest point.
3. Lower the outfeed table until the straight edge contacts a knife blade. Rock the head slightly to make sure the apex of the knife is contacting the straight edge.
4. Lock the outfeed table at this setting.
Too high | Just right | Too low |
---|---|---|
Workpiece curved on bottom | Workpiece flat on bottom | Workpiece gouged at end |