Burr King Belt Sander: Difference between revisions

From Artisans Asylum Wiki
(Created page with "Category:ToolsCategory:Metal Shop Link to: Metal Shop main page Link to: Metal Shop tool list {{ToolBox |tool_title=2x48-Inch Three-Wheel Belt Sander |image=Burr_king_nolabels.png |caption=Hold the Pickle, Hold the Lettuce. |location=Metal Shop |training={{AAClass_MET_1}} |testing=[https://www.artisansasylum.com/tool-testing Tool testing], or :Category:Metal Shop#Tool...")
 
 
(29 intermediate revisions by the same user not shown)
Line 4: Line 4:


Link to:  [[:Category:Metal Shop#Tools | Metal Shop tool list]]
Link to:  [[:Category:Metal Shop#Tools | Metal Shop tool list]]
Use of this tool is taught in {{:AAClass_MET_1}}


{{ToolBox
{{ToolBox
Line 10: Line 12:
     |caption=Hold the Pickle, Hold the Lettuce.
     |caption=Hold the Pickle, Hold the Lettuce.
     |location=Metal Shop
     |location=Metal Shop
     |training={{AAClass_MET_1}}
     |training={{:AAClass_MET_1}}
     |testing=[https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing Night|come to the shop on Tool Testing Night]]
     |testing=[https://www.artisansasylum.com/tool-testing Tool testing], or [[:Category:Metal Shop#Tool Testing Night|come to the shop on Tool Testing Night]]
     |restrictions=red
     |restrictions=red
Line 27: Line 29:


This free-standing sanding machine drives a 2-inch wide abrasive belt vertically down behind a small table that supports the workpiece.  A vertical backing plate presses back against the pressure on the workpiece.  The machine has a variable-speed control and a dust collector.  Its three-wheel architecture makes it easier to control the belt tension.
This free-standing sanding machine drives a 2-inch wide abrasive belt vertically down behind a small table that supports the workpiece.  A vertical backing plate presses back against the pressure on the workpiece.  The machine has a variable-speed control and a dust collector.  Its three-wheel architecture makes it easier to control the belt tension.
''Please Note:'' If you plan to use this tool extensively, you should probably buy your own belts.  The supply in the Metal Shop is limited.  One way to find them is to run a Google search for: "2x48 sanding belts".


== Use for: ==
== Use for: ==
Hard and soft metals
Hard and soft metals
Some plastics
Some plastics
Small bits of wood


== Do not use for: ==
== Do not use for: ==
Toxic materials
Toxic or highly flammable materials
 
Glass and ceramics
 
Minerals
 
Grinding off your fingertips


== Safety Hazards ==
== Safety Hazards ==
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Burr_King_dust_collector_switch.jpg|250px|dust collector on/off ]]
|-
| colspan="2" |  To turn on the dust collector, pull the red lever up.  Push down to turn off.
|-
|}
* '''ALWAYS WEAR EYE PROTECTION!!''' Face shield is recommended.
* Do not use the machine if you haven't been properly trained.
* ALWAYS turn on the [https://drive.google.com/file/d/1-Rc5vS-uFCAGgUfonfjKs8-yK4BwYX60/view?usp=drive_link '''Dust Collector'''] before operating the machine.
* Keep fingers and hands away from the moving belt.
* When possible, grip the workpiece with vise grips to protect the hands from abrasion and excessive heat.
* Do not wear gloves.  Fabric gloves can be sucked into the machine by the moving belt, causing serious hand injury.
* Beware of sparks showering from the machine during grinding. 
* Do not allow piles of metal powder to accumulate inside the machine.  Sparks can cause a fire.
* Do not operate the machine if the gap between the belt and the support table exceeds 1/8".
* Avoid mixing different metals on the same belt.  Chemical reactions during grinding may cause a fire.
* Do not run the belt sander motor in reverse.  The workpiece may be kicked into your face.
=Speed Control=
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Burr_King_controller.png|150px|sander speed control ]]
|-
| colspan="2" |  The VEVOR speed control mounted on the Burr King sander.
|-
|}
Power for the Burr King sander is supplied with a toggle switch to the right of the controller.  The speed control must be used to start and stop the motor, and the speed of the belt can be adjusted using it.
DO NOT attempt to change the settings unless you have been properly trained, tool-tested and you have read the [https://drive.google.com/file/d/1XMXzkzpwMiFUSxIsxKXhjcZVtgY_yasT/view?usp=drive_link user manual] for the controller!
The display on the controller reads the output frequency going to the motor, not the motor speed.  Unless you have done a lot of homework, this number won't have any use to you.
The motor can be started and stopped using the green and red buttons on the front panel.
=Changing the Belt=
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Burr_king_belt_tensioner.png|200px|belt tensioner ]]
|-
| colspan="2" |  The belt tensioning handle inside the housing
|-
|}
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Burr_king_side_door_open.png|187px|side door open ]]
|-
| colspan="2" |  To access the belt, open the door on the right side of the machine.
|-
|}
The process for tensioning the belt is described on page 10 of the [https://drive.google.com/file/d/17dlYvfwkayPyTciZfODPw4VNSkVSiqpl/view?usp=drive_link User Manual.]
Open the door on the right side of the machine.
Press the button in the center of the tensioning handle to release the ratchet. 
Move the handle down to free up the belt.
Remove the old belt and replace.
To tension, lift the handle up until the ratchet clicks several times.
The belt is properly tensioned after the pawl has clicked between 3 and 8 times.
Close the side door on the machine.

Latest revision as of 21:24, 13 October 2024


Link to: Metal Shop main page

Link to: Metal Shop tool list

Use of this tool is taught in Metal Shop 101


2x48-Inch Three-Wheel Belt Sander
Hold the Pickle, Hold the Lettuce.
General Info
Make Burr King
Model 482
Serial Unknown
Specs n/a
Manual Burr King 482 Manual
Asylum Info
Location Metal Shop
Rubric n/a
Training Metal Shop 101
Testing Tool testing, or come to the shop on Tool Testing Night
Restrictions red


Warning Safety glasses Eye protection required!


Description

This free-standing sanding machine drives a 2-inch wide abrasive belt vertically down behind a small table that supports the workpiece. A vertical backing plate presses back against the pressure on the workpiece. The machine has a variable-speed control and a dust collector. Its three-wheel architecture makes it easier to control the belt tension.

Please Note: If you plan to use this tool extensively, you should probably buy your own belts. The supply in the Metal Shop is limited. One way to find them is to run a Google search for: "2x48 sanding belts".

Use for:

Hard and soft metals

Some plastics

Small bits of wood

Do not use for:

Toxic or highly flammable materials

Glass and ceramics

Minerals

Grinding off your fingertips

Safety Hazards

dust collector on/off
To turn on the dust collector, pull the red lever up. Push down to turn off.
  • ALWAYS WEAR EYE PROTECTION!! Face shield is recommended.
  • Do not use the machine if you haven't been properly trained.
  • Keep fingers and hands away from the moving belt.
  • When possible, grip the workpiece with vise grips to protect the hands from abrasion and excessive heat.
  • Do not wear gloves. Fabric gloves can be sucked into the machine by the moving belt, causing serious hand injury.
  • Beware of sparks showering from the machine during grinding.
  • Do not allow piles of metal powder to accumulate inside the machine. Sparks can cause a fire.
  • Do not operate the machine if the gap between the belt and the support table exceeds 1/8".
  • Avoid mixing different metals on the same belt. Chemical reactions during grinding may cause a fire.
  • Do not run the belt sander motor in reverse. The workpiece may be kicked into your face.

Speed Control

sander speed control
The VEVOR speed control mounted on the Burr King sander.

Power for the Burr King sander is supplied with a toggle switch to the right of the controller. The speed control must be used to start and stop the motor, and the speed of the belt can be adjusted using it.

DO NOT attempt to change the settings unless you have been properly trained, tool-tested and you have read the user manual for the controller!

The display on the controller reads the output frequency going to the motor, not the motor speed. Unless you have done a lot of homework, this number won't have any use to you.

The motor can be started and stopped using the green and red buttons on the front panel.

Changing the Belt

belt tensioner
The belt tensioning handle inside the housing
side door open
To access the belt, open the door on the right side of the machine.

The process for tensioning the belt is described on page 10 of the User Manual.

Open the door on the right side of the machine.

Press the button in the center of the tensioning handle to release the ratchet.

Move the handle down to free up the belt.

Remove the old belt and replace.

To tension, lift the handle up until the ratchet clicks several times.

The belt is properly tensioned after the pawl has clicked between 3 and 8 times.

Close the side door on the machine.

Retrieved from "http://wiki.artisansasylum.com/index.php?title=Burr_King_Belt_Sander&oldid=5320"