Powermatic PJ1696 Jointer: Difference between revisions
From Artisans Asylum Wiki
No edit summary |
No edit summary |
||
Line 97: | Line 97: | ||
* Do NOT wear gloves | * Do NOT wear gloves | ||
==Setting the Outfeed Table== | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_outfeed_high.png|350px|outfeed high]] | |||
|- | |||
| colspan="2" | If the outfeed table is too high, the cut depth will taper along the length of the workpiece. | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_outfeed_correct.png|350px|outfeed correct]] | |||
|- | |||
| colspan="2" | The correct height for the outfeed is exactly level with the cutting blades. | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:Jointer_outfeed_low.png|350px|outfeed low]] | |||
|- | |||
| colspan="2" | If the outfeed table is too low, the end of the cut gets gouged too deeply. | |||
|- | |||
|} |
Revision as of 14:44, 17 February 2024
Powermatic 16" Jointer | |
---|---|
General Info | |
Make | Powermatic |
Model | PJ1696 |
Serial | Unknown |
Specs | |
Manual | Jointer User Manual |
Asylum Info | |
Location | Wood Shop |
Rubric | |
Training | |
Testing | |
Restrictions | red |
This is a RED tool. Training and tool-testing are required.
Use For
Wooden boards only
Length > 8 inches
Width > 3/4"
Wood with uneven grain requires special care.
Do Not Use For
Fiberboard
Plastics
Composites
Metals
Eye protection required! | ||
---|---|---|
Safety Notes
Personal:
Don't chop off your fingers! |
- Eye protection required
- Hearing protection recommended
- No loose clothing or jewelry, roll up sleeves above the elbows.
- Tie up or cover long hair
- Closed-toe shoes with good traction.
Tool:
- Make sure guards are in place and working well.
- Switch on Dust Collector: Coral free-standing 2-filter between 1696 Jointer and 201 Planer
- Keep hands at least 3 inches away from the blades at all times.
- Don't cut wood less than 8" long, 3/4" wide or 1/4" thick.
Shift hands during cut. MAINTAIN PRESSURE ON THE WORKPIECE. |
- For wood less than 12" long, 3" wide and 3" thick, a hold-down or push block is required
- Never apply pressure to stock directly above the cutter head. This can lead to the stock tipping into the cutter.
- Wood grain must run in the direction of the cutting.
- Never make cuts greater then 1/8" deep
- Do NOT wear gloves
Setting the Outfeed Table
If the outfeed table is too high, the cut depth will taper along the length of the workpiece. |
The correct height for the outfeed is exactly level with the cutting blades. |
If the outfeed table is too low, the end of the cut gets gouged too deeply. |