Abrasive Blade Metal Chop Saw: Difference between revisions
From Artisans Asylum Wiki
No edit summary |
No edit summary |
||
Line 69: | Line 69: | ||
==Basic Operation Instructions and Best Practices== | ==Basic Operation Instructions and Best Practices== | ||
1. Before operation, perform a quick safety check: | '''1. Before operation, perform a quick safety check:''' | ||
* Never use a damaged cutting wheel — Inspect for cracks or flaws. '''Damaged wheels may break or shatter during saw operation.''' | * Never use a damaged cutting wheel — Inspect for cracks or flaws. '''Damaged wheels may break or shatter during saw operation.''' | ||
* Remove anything from behind the saw before operating. | * Remove anything from behind the saw before operating. | ||
'''2. Secure work piece in the chop saw’s vise.''' | |||
* Work piece must fill vise to at least center of the vise’s back fence. | |||
* Prevent mishaps: Understand how the rotating blade will try to move your part in the vise and position / stabilize your workpiece accordingly. (See Clamping Tips below.) | |||
* Use the vise lever to fasten the workpiece, then tighten securely by turning the vise crank. (See features H and I.) | |||
'''3. Perform the cut.''' | |||
* Watch where you stand - avoid line of cutting wheel. Sparks and small pieces will tend to kick back toward wall, but can fly in any direction. | |||
* Never start with cutting wheel inserted into or touching the workpiece. Press handle trigger to start the blade, then lower the blade. | |||
* Vary force and travel speed to match the shape of work – judge by ear and by the sparks produced. No quick chops. | |||
'''Clamping Tips''' | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
Line 81: | Line 99: | ||
|- | |- | ||
|} | |} | ||
'''Be aware of blade rotation.''' | |||
Angles are best cut with both legs facing down. This allows a safe cut, but is not optimal for miter cuts. | |||
Another option for Angles: L facing backward, into the rotation of the blade. | |||
Use square tube as a stabilizer. A spacer block slightly more narrow than the work piece can increase blade utilization. | |||
Long workpieces must be supported to remain level. The cut-off end should be free to fall in order to avoid wheel binding. |
Revision as of 15:15, 9 February 2024
Abrasive Blade Chop Saw | |
---|---|
General Info | |
Make | Dewalt |
Model | D28710 |
Serial | Unknown |
Specs | |
Manual | |
Asylum Info | |
Location | Metal Shop |
Rubric | |
Training | Tool classes |
Testing | Tool testing, or [[:Category:Metal Shop#Tool Testing
Night|come to the shop on Tool Testing Night]] |
Restrictions | red |
Metal Shop
Use for:
- Hardened Steel
- Mild Steel
Do Not Use for:
- Aluminum
- Copper, Brass, Bronze
Soft metals will gum up the abrasive cutting disk.
- Zinc (or anything galvanized).
- Titanium
Hazard Analysis
- Tool is very loud. Hearing protection required.
- Flying pieces from broken abrasive discs/ blades. Eye protection required.
- Prevent drawn-in injuries. No loose clothing or gloves.
- Cuts/ scrapes from sharp cut edges of work•Burns from hot work pieces
- Breathing particulates thrown into the air. Respiratory protection recommended.
Operation Notes
Eye protection required! | ||
---|---|---|
Dangerous clutter behind the Chop Saw |
Basic Operation Instructions and Best Practices
1. Before operation, perform a quick safety check:
- Never use a damaged cutting wheel — Inspect for cracks or flaws. Damaged wheels may break or shatter during saw operation.
- Remove anything from behind the saw before operating.
2. Secure work piece in the chop saw’s vise.
- Work piece must fill vise to at least center of the vise’s back fence.
- Prevent mishaps: Understand how the rotating blade will try to move your part in the vise and position / stabilize your workpiece accordingly. (See Clamping Tips below.)
- Use the vise lever to fasten the workpiece, then tighten securely by turning the vise crank. (See features H and I.)
3. Perform the cut.
- Watch where you stand - avoid line of cutting wheel. Sparks and small pieces will tend to kick back toward wall, but can fly in any direction.
- Never start with cutting wheel inserted into or touching the workpiece. Press handle trigger to start the blade, then lower the blade.
- Vary force and travel speed to match the shape of work – judge by ear and by the sparks produced. No quick chops.
Clamping Tips
Chop Saw clamping tips |
Be aware of blade rotation.
Angles are best cut with both legs facing down. This allows a safe cut, but is not optimal for miter cuts.
Another option for Angles: L facing backward, into the rotation of the blade.
Use square tube as a stabilizer. A spacer block slightly more narrow than the work piece can increase blade utilization.
Long workpieces must be supported to remain level. The cut-off end should be free to fall in order to avoid wheel binding.