Hydraulic Shop Press: Difference between revisions
From Artisans Asylum Wiki
No edit summary |
|||
| Line 59: | Line 59: | ||
|- | |- | ||
| colspan="2" | Transverse bending tool. | | colspan="2" | Transverse bending tool. | ||
|- | |||
|} | |||
=Bending= | |||
* Mark your workpiece with a clearly visible line. | |||
* Insert the workpiece into the jig and lower the workpiece so it lightly loads. | |||
* Square the workpiece in the tool. | |||
* Pump up the pressure to bend the workpiece. | |||
* Check the angle with a square as the bend approaches 90°. If you squeeze too far, the bend can surpass 90°. | |||
{| class="infobox" cellspacing="5" style="width: 2em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:bending_a_piece.png|210px|bending]] | |||
|- | |||
| colspan="2" | Bend | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="5" style="width: 2em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:squaring_a_piece.png|210px|squaring]] | |||
|- | |||
| colspan="2" | Square | |||
|- | |||
|} | |||
{| class="infobox" cellspacing="5" style="width: 2em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:marking_a_piece.png|210px|marking]] | |||
|- | |||
| colspan="2" | Mark | |||
|- | |- | ||
|} | |} | ||
Revision as of 19:34, 6 September 2024
Link to: Metal Shop main page
Link to: Metal Shop tool list
| 12-Ton Shop Press | |
|---|---|
| General Info | |
| Make | Duralast |
| Model | 12-ton |
| Serial | Unknown |
| Specs | n/a |
| Manual | n/a |
| Asylum Info | |
| Location | Metal Shop |
| Rubric | n/a |
| Training | Tool classes |
| Testing | Tool testing, or come to the shop on Tool Testing Night |
| Restrictions | green |
Description
| |
|---|---|
| Pressure relief |
This is a 12-ton hydraulic "bottle" jack mounted to a steel frame so it can be used as a press. The pressure relief valve is located on the press base. This machine is generally used for bending sheets and bars, and it usually has a 4" wide right-angle bending tool and die set mounted. The opening in the frame is 16" wide.
Use for:
- Bending steel sheets and bars up to 1/8" thick
Do not use for:
- High-carbon or Hardened steel
- Round or square stock
Safety Hazards
 |
 |
Eye protection required! |
|---|---|---|
- Workpiece can unexpectedly snap
- Pinching injuries
- Cuts/scrapes from sharp edges and burrs
Tooling
The bending tool is press-fit onto the ram below the bottle jack. It can be positioned at any angle, but the two most useful orientations are shown here: longitudinal and transverse.
To remove the tool, hit it with a "dead-blow" hammer with a soft head until it lossens up and comes off. Reposition, and press it onto the ram using the press.
| |
|---|---|
| Removing the tool with a "dead-blow" hammer. |
| |
|---|---|
| Longitudinal bending tool. |
| |
|---|---|
| Transverse bending tool. |
Bending
- Mark your workpiece with a clearly visible line.
- Insert the workpiece into the jig and lower the workpiece so it lightly loads.
- Square the workpiece in the tool.
- Pump up the pressure to bend the workpiece.
- Check the angle with a square as the bend approaches 90°. If you squeeze too far, the bend can surpass 90°.
| |
|---|---|
| Bend |
| |
|---|---|
| Square |
| |
|---|---|
| Mark |
