Category:Vertical Band Saws -- Wood Cutting

From Artisans Asylum Wiki
Revision as of 17:24, 24 February 2024 by Jfbredt (talk | contribs)



Wood Cutting Band Saw
Band Saw PM1500 "Bullwinkle" in the Wood Shop
General Info
Make
Model
Serial
Specs
Manual
Asylum Info
Location [[:Category:|]]
Rubric
Training
Testing
Restrictions

[[Category:]]


There are two tools in the Wood Shop in this category:

PM1500 Band Saw "Bullwinkle"

PWBS-14 Band Saw "Rocky"


User Manuals:

Link to: Powermatic PM1500 Manual

Link to: Powermatic PWBS-14 Manual

Description

The cutting blade in a band saw is a continuous loop that travels through the machine on pulleys. In a vertical band saw, the blade travels vertically through a slot in a table, and workpieces are hand-fed through the blade to make a cut.

Wood-grain affects the forces and motions during cutting in a saw, so there is a ripping fence and a miter gauge as in a table saw. With metal cutting, the workpiece is usually clamped in a vise.

Band saw parts
Parts of a typical band saw.

Use For

  • Dry, flat lumber
  • Boards
  • Plywood sheets that fit within the tool width
  • Logs, carvings, or other irregular lumber if supported properly
  • Making curved cuts (within the tolerance of the blade)

Do Not Use For

  • Pressure-treated
  • Wet lumber
  • Plastic
  • Metal or metal-coated
  • Composites
Cutting radii
Cutting radii with various width of blade.

Safety Notes

Whirling blades hazard.png


This is a convenient and familiar tool that can deceive the user into being casual with its operation.

Do not relax safety protocols or or treat this tool as anything but a potentially lethal hazard.

Warning Eye and lung protection Eye and lung protection required!


Personal:

  • Always wear safety glasses. Eyeglasses are not safety glasses.
Band saw blade
Keep fingers away!
  • No loose clothing. Tie up long hair. No jewelry.
  • Wear non-slip shoes and keep a stable stance to avoid falling or leaning against the blade.
  • Do not wear gloves. Gloves can be drawn in by the moving blade, causing very serious injury.
  • Hearing protection is recommended.
  • Always use the dust collector. Both band saws in the Wood Shop are connected to the central dust collector (Coral AF/4C)
Warning Dust collection required Dust collection required!


  • All forms of dust are hazardous. Wear a dust mask to avoid exposure.
  • Do not cut hazardous materials such as pressure-treated lumber.

Tool:

  • Always lower the blade guard to the lowest point that will allow a cut.
  • Always unplug the tool before servicing.
  • Remove adjusting keys and wrenches before switching on the tool.
  • Keep safety guards in place at all times.
Rip fence
A generic rip fence. Fences on saws in the Wood Shop may have a different profile.
  • Use a push stick when feeding small pieces into the saw.
  • If the blade jams during cutting, switch off the power and allow the machine to come to a complete stop.
  • If the blade comes off the drive pulleys, refer to the equipment manual for the particular unit for instructions on how to re-seat it and set the tension.

Accessories

Rip Fence

Wood-cutting band saws have similar accessories to those on a table saw. The most important is the rip fence.

This accessory guides the workpiece lengthwise at a fixed distance through the blade. It clamps in place using the handle shown.

Important Use a push stick to finish cuts. Keep hands and fingers away from the blade at all times.

Miter gauge
A generic miter gauge.

Miter Gauge

A miter gauge is used for cross-cutting or for making miter cuts. To use it, remove the rip fence and seat the gauge in the slot on the table.

This accessory has an adjustable angle that may be set to achieve miter cuts as small as 30 degrees with respect to the feed direction.

Never cross the hands over the line of the cut when feeding a workpiece into the saw.

Always keep the blade guard down as far as possible.

Tilting the table

Many band saws have a feature allowing the operator to tilt the table to make bevel cuts. Please check with the shop lead whether these types of cuts are allowed on a particular tool.

Table tilt
Underneath the table there may be a tilting gauge for bevel cuts.

Pages in category "Vertical Band Saws -- Wood Cutting"

The following 2 pages are in this category, out of 2 total.