General Hydraulic Shop Press: Difference between revisions
From Artisans Asylum Wiki
No edit summary |
|||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
[[Category:Machine Shop]] | [[Category:Machine Shop]] | ||
Link to: [[:Category:Machine Shop | Machine | Link to: [[:Category:Machine Shop | Machine Shop Main Page]] | ||
{{ToolBox | {{ToolBox | ||
| Line 9: | Line 9: | ||
|caption = The 20-ton Hydraulic Shop Press | |caption = The 20-ton Hydraulic Shop Press | ||
|make = General Hydraulic | |make = General Hydraulic | ||
|model = | |model = 20-ton | ||
|serial = | |serial = | ||
|manufacturer_specs = | |manufacturer_specs = | ||
| Line 20: | Line 20: | ||
|tool_categories = | |tool_categories = | ||
}} | }} | ||
=Description= | |||
A hydraulic jack mounted to a frame that translates the lifting force into pressure. Built around a Pittsburgh 20-ton bottle jack. Width: 18 inches. Also includes a jig for bending metal sheet. It has a compressed-air actuator built in but can also be operated manually. | |||
==Use For== | |||
Squashing things | |||
==Do Not Use For== | |||
Not squashing things | |||
=Bending Accessory= | |||
{| class="infobox" cellspacing="5" style="width: 12em; text-align: left; font-size: 100%; line-height: 1.5em;" | |||
! colspan="2" class="infobox-image" | [[File:hydraulic_press_bending_jig.jpg|250px| bending jig]] | |||
|- | |||
| colspan="2" | The bending jig for the 20-ton shop press | |||
|- | |||
|} | |||
This accessory normally rests on the floor behind the press. Caution! Weight is about 60 lbs. | |||
It is constructed over a piece of 3" x 3" x <sup>5</sup>/<sub>16</sub>" angle, so the bends it makes are distributed through about 4" of width. To tighten up the bend radius, stack pieces of smaller angle inside the large one. | |||
Loads to bend steel sheet can be found on this [https://www.americanmachinetools.com/pressure_table.htm tonnage chart]. Do not exceed 20 tons. | |||
Latest revision as of 21:50, 14 June 2024
Link to: Machine Shop Main Page
| Hydraulic Shop Press | |
|---|---|
| General Info | |
| Make | General Hydraulic |
| Model | 20-ton |
| Serial | |
| Specs | |
| Manual | Pittsburgh 20-ton Bottle Jack Manual |
| Asylum Info | |
| Location | Machine Shop |
| Rubric | N/A |
| Training | |
| Testing | Tool testing |
| Restrictions | green |
Description
A hydraulic jack mounted to a frame that translates the lifting force into pressure. Built around a Pittsburgh 20-ton bottle jack. Width: 18 inches. Also includes a jig for bending metal sheet. It has a compressed-air actuator built in but can also be operated manually.
Use For
Squashing things
Do Not Use For
Not squashing things
Bending Accessory
| |
|---|---|
| The bending jig for the 20-ton shop press |
This accessory normally rests on the floor behind the press. Caution! Weight is about 60 lbs.
It is constructed over a piece of 3" x 3" x 5/16" angle, so the bends it makes are distributed through about 4" of width. To tighten up the bend radius, stack pieces of smaller angle inside the large one.
Loads to bend steel sheet can be found on this tonnage chart. Do not exceed 20 tons.
