Dake Drill Press: Difference between revisions
No edit summary |
No edit summary |
||
| (11 intermediate revisions by the same user not shown) | |||
| Line 11: | Line 11: | ||
|manufacturer_specs = | |manufacturer_specs = | ||
|manual = [https://drive.google.com/file/d/14J0h45qFgf-qJkPHPmnZNXctXAPnbJkK/view?usp=drive_link Dake SB-32V manual] | |manual = [https://drive.google.com/file/d/14J0h45qFgf-qJkPHPmnZNXctXAPnbJkK/view?usp=drive_link Dake SB-32V manual] | ||
|location = Metal Shop | |location = Metal Shop and Machine Shop | ||
|rubric = | |rubric = | ||
|training = | |training = | ||
|testing = | |testing = | ||
|restrictions = | |restrictions = green | ||
|tool_categories = [[:Category:Drill Presses|See the Drill Presses category for notes on using all Drill Presses]] | |tool_categories = [[:Category:Drill Presses|See the Drill Presses category for notes on using all Drill Presses]] | ||
}} | }} | ||
There is one unit in the [[Metal Shop]] and one unit in the [[:Category:Machine Shop|Machine Shop]] | |||
Link to: [[:Category:Metal Shop#Tools | Metal Shop tool list]] | |||
{{EyeWarning}} | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
| Line 27: | Line 31: | ||
|- | |- | ||
|} | |} | ||
'''To start''' | |||
1. Disengage the E-STOP button (left, bottom) | |||
2. Turn the switch (right,bottom) to the desired direction. ''Forward is 99% of the useful cases'' | |||
3. The spindle speed can be adjusted with the small black knob top right. | |||
'''To Stop''' | |||
1. Turn the three-position switch (bottom, right) to OFF. | |||
2. Alternatively, push the E-STOP button. | |||
'''NOTE:''' The Dake speed control knob adjusts the speed over a moderate range. To make large changes to the spindle speed: | |||
1. Unplug the drill press | |||
2. Open the belt/pulley cover | |||
3. Loosen the belt-tensioning lock handle on the right side just in front of the motor. | |||
4. Check the table of belt and pulley configurations. In the Metal Shop a hardcopy of the table is attached to the speed control box. You can also look at p. 15 of the [https://drive.google.com/file/d/14J0h45qFgf-qJkPHPmnZNXctXAPnbJkK/view?usp=drive_link Dake SB-32V manual]. | |||
5. Reconfigure the belts as desired. | |||
6. Tension the belts by pushing the motor back and tightening the lock handle. | |||
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | {| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;" | ||
! colspan="2" class="infobox-image" | [[File:Dake_pulleys_w_Scraps_behind.jpg| | ! colspan="2" class="infobox-image" | [[File:Dake_pulleys_w_Scraps_behind.jpg|550px|Dake pulley set]] | ||
|- | |- | ||
| colspan="2" | The Dake drill press has a third idler pulley in the power train. | | colspan="2" | The Dake drill press has a third idler pulley in the power train. | ||
|- | |- | ||
|} | |} | ||
7. The belt shouldn't be too tight. It should be possible to deflect the belt 1/2" by pressing with a finger. | |||
8. Close the belt/pulley cover. | |||
9. Plug the machine back in. | |||
Latest revision as of 21:10, 5 September 2024
| Dake Drill Press | |
|---|---|
| General Info | |
| Make | Dake |
| Model | SB-32V |
| Serial | Unknown |
| Specs | |
| Manual | Dake SB-32V manual |
| Asylum Info | |
| Location | Metal Shop and Machine Shop |
| Rubric | |
| Training | |
| Testing | |
| Restrictions | green |
See the Drill Presses category for notes on using all Drill Presses
There is one unit in the Metal Shop and one unit in the Machine Shop
Link to: Metal Shop tool list
 |
 |
Eye protection required! |
|---|---|---|
| |
|---|---|
| The Dake drill press is reversible with variable speed control. |
To start
1. Disengage the E-STOP button (left, bottom)
2. Turn the switch (right,bottom) to the desired direction. Forward is 99% of the useful cases
3. The spindle speed can be adjusted with the small black knob top right.
To Stop
1. Turn the three-position switch (bottom, right) to OFF.
2. Alternatively, push the E-STOP button.
NOTE: The Dake speed control knob adjusts the speed over a moderate range. To make large changes to the spindle speed:
1. Unplug the drill press
2. Open the belt/pulley cover
3. Loosen the belt-tensioning lock handle on the right side just in front of the motor.
4. Check the table of belt and pulley configurations. In the Metal Shop a hardcopy of the table is attached to the speed control box. You can also look at p. 15 of the Dake SB-32V manual.
5. Reconfigure the belts as desired.
6. Tension the belts by pushing the motor back and tightening the lock handle.
| |
|---|---|
| The Dake drill press has a third idler pulley in the power train. |
7. The belt shouldn't be too tight. It should be possible to deflect the belt 1/2" by pressing with a finger.
8. Close the belt/pulley cover.
9. Plug the machine back in.
