Bridgeport Series 1 Standard Knee Mill: Difference between revisions

From Artisans Asylum Wiki
(basic template in place)
No edit summary
 
(5 intermediate revisions by 2 users not shown)
Line 1: Line 1:
[[Category:Tools]][[Category:Milling Machines]]
[[Category:Tools]][[Category:Milling Machines]]
{{ToolBox|tool_title=Bridgeport Series 1 Standard Knee Mill|image=Bridgeport.jpg|caption=Bridgeport|make=Bridgeport|model=Series 1|serial=J292372|manufacturer_specs=[https://bridgeportmachinetools.com/product/milling/series-1/ specs]|location=Machine Shop|training=[https://www.artisansasylum.com/class-catalog Tool classes]|testing=[https://www.artisansasylum.com/tool-testing Tool testing]|restrictions=red|tool_categories=[[Category:Milling Machines]]}}
 
{{ToolBox
  |tool_title=Bridgeport Series 1 Standard Knee Mill
  |image=Bridgeport.jpg
  |caption=Bridgeport
  |make=Bridgeport
  |model=Series 1
  |serial=J292372
  |manufacturer_specs=[https://bridgeportmachinetools.com/product/milling/series-1/ specs]
  |location=Machine Shop|training=[https://www.artisansasylum.com/class-catalog Tool classes]
  |testing=[https://www.artisansasylum.com/tool-testing Tool testing]
  |restrictions=red
  |tool_categories=[[:Category:Milling Machines | See the Milling Machines category for notes on using all 3-Axis Milling Machines]]
}}


Link to:[[:Category:Machine Shop | Machine Shop Main Page]]
Link to:[[:Category:Machine Shop | Machine Shop Main Page]]
Line 6: Line 19:
== Safety Information ==
== Safety Information ==
{{EyeWarning}}
{{EyeWarning}}
Link to:  [https://wiki.artisansasylum.com/wiki/Category:Milling_Machines#Safety_Notes Safety notes on the Milling Machine Category page]
== Operating Instructions ==
Textbook: [https://drive.google.com/file/d/1FAn64l7N04PFASki_5Y7g0cwydGGAuEp/view?usp=drive_link  How to Operate a Milling Machine ]
=== Calibration  ===
To account for the error caused by inconsistent collet seating in the spindle, it is recommended to check the calibration of the Pro Tram Gage every time it is used. Completing the steps below will position the two indicator tips on a theoretical line that is perpendicular to the spindles axis.
* Install the Pro Tram into spindle.
* Place calibration magnet on the table under one of the indicators.
* Lower spindle until indicator is depressed about 0.100”. Then lock the spindle in place. Be sure to lock the knee of the mill as well.
* Rotate the face of the indicator until the needle reads zero. Then rotate the Pro Tram unit 180 degrees so that the other indicator is contacting the calibration magnet.
* Rotate the face of the second indicator until the needle reads zero.  
* After calibration the right and left indicator faces may be rotated to slightly different positions. This is caused by a slight variance in indicator length and will not affect the functionality of the unit.
=== Operation ===


== Materials Information ==
* Install the Pro Tram into the spindle. Lock the knee of the mill.
* Position the Pro Tram parallel to the length of the milling machine table. Then lower the spindle until both indicators are depressed by about 0.050”.
* Make adjustments to the head of the milling machine until both indicators read the same number. When this is accomplished the first axis of the milling machine is trammed.
* Position the Pro Tram perpendicular to the length of the milling machine table. Then lower the spindle until both indicators are depressed by about 0.050”.
* Make adjustments to the head of the milling machine until both indicators read the same number. When this is accomplished the second axis of the mill is trammed.
{{Warning|text='''Caution''' When installing or removing the Pro Tram from the spindle keep at least one hand on the unit while tightening or loosening the draw bar. This will prevent the unit from accidently falling out of the spindle. If necessary put the machine in low gear to eliminate the need to hold the machine brake lever while tightening or loosening the draw bar.}}
 
==Speed Adjustment==
 
{| class="infobox" cellspacing="5" style="width: 22em; text-align: left; font-size: 100%; line-height: 1.5em;"
! colspan="2" class="infobox-image" | [[File:Mill_Bridgeport_speed_control.png|250px|Tortoise and hare]]
|-
| colspan="2" |  The speed control on the Bridgeport mill.
|-
|}
 
The spindle speed is adjusted manually with the crank on the right-hand face of the headstock.  '''Only adjust the spindle speed when the spindle is turning!'''
 
A range-control lever on the left side of the headstock switches between "Tortoise" and "Hare" speed ranges.  '''Change the position of this lever only when the spindle is stopped!''' The spindle may need to be rotated manually when changing the speed range to allow the gears to mesh.  The direction of the spindle reverses between the two modes (note the directions the two animals are facing) and the motor power switch on the left shows the two directions for "forward" rotation in each mode.
 
This machine has variable-speed motor drives (Not CNC) on the two axes of the table.
 
==Manual Draw-Bar==
 
This machine has manual tool-changing with a wrench.


== Operating Instructions ==


== Maintenance ==
== Maintenance ==


== Common problems and troubleshooting information ==
== Common problems and troubleshooting information ==

Latest revision as of 13:26, 14 October 2024



Bridgeport Series 1 Standard Knee Mill
Bridgeport
General Info
Make Bridgeport
Model Series 1
Serial J292372
Specs specs
Manual {{{manual}}}
Asylum Info
Location Machine Shop
Rubric {{{rubric}}}
Training Tool classes
Testing Tool testing
Restrictions red

See the Milling Machines category for notes on using all 3-Axis Milling Machines


Link to: Machine Shop Main Page

Safety Information

Warning Safety glasses Eye protection required!


Link to: Safety notes on the Milling Machine Category page

Operating Instructions

Textbook: How to Operate a Milling Machine

Calibration 

To account for the error caused by inconsistent collet seating in the spindle, it is recommended to check the calibration of the Pro Tram Gage every time it is used. Completing the steps below will position the two indicator tips on a theoretical line that is perpendicular to the spindles axis.

  • Install the Pro Tram into spindle.
  • Place calibration magnet on the table under one of the indicators.
  • Lower spindle until indicator is depressed about 0.100”. Then lock the spindle in place. Be sure to lock the knee of the mill as well.
  • Rotate the face of the indicator until the needle reads zero. Then rotate the Pro Tram unit 180 degrees so that the other indicator is contacting the calibration magnet.
  • Rotate the face of the second indicator until the needle reads zero.  
  • After calibration the right and left indicator faces may be rotated to slightly different positions. This is caused by a slight variance in indicator length and will not affect the functionality of the unit.

Operation

  • Install the Pro Tram into the spindle. Lock the knee of the mill.
  • Position the Pro Tram parallel to the length of the milling machine table. Then lower the spindle until both indicators are depressed by about 0.050”.
  • Make adjustments to the head of the milling machine until both indicators read the same number. When this is accomplished the first axis of the milling machine is trammed.
  • Position the Pro Tram perpendicular to the length of the milling machine table. Then lower the spindle until both indicators are depressed by about 0.050”.
  • Make adjustments to the head of the milling machine until both indicators read the same number. When this is accomplished the second axis of the mill is trammed.
Warning Caution When installing or removing the Pro Tram from the spindle keep at least one hand on the unit while tightening or loosening the draw bar. This will prevent the unit from accidently falling out of the spindle. If necessary put the machine in low gear to eliminate the need to hold the machine brake lever while tightening or loosening the draw bar.


Speed Adjustment

Tortoise and hare
The speed control on the Bridgeport mill.

The spindle speed is adjusted manually with the crank on the right-hand face of the headstock. Only adjust the spindle speed when the spindle is turning!

A range-control lever on the left side of the headstock switches between "Tortoise" and "Hare" speed ranges. Change the position of this lever only when the spindle is stopped! The spindle may need to be rotated manually when changing the speed range to allow the gears to mesh. The direction of the spindle reverses between the two modes (note the directions the two animals are facing) and the motor power switch on the left shows the two directions for "forward" rotation in each mode.

This machine has variable-speed motor drives (Not CNC) on the two axes of the table.

Manual Draw-Bar

This machine has manual tool-changing with a wrench.


Maintenance

Common problems and troubleshooting information

Retrieved from "http://wiki.artisansasylum.com/index.php?title=Bridgeport_Series_1_Standard_Knee_Mill&oldid=5343"